16.11.2026

How to clean your aircraft with Aero-Sense® Airframe Dry Wash

A step-by-step guide to waterless exterior cleaning

Keeping an aircraft's exterior clean is an important part of regular aircraft maintenance. Dirt, oil, grease and exhaust residue can accumulate on aircraft surfaces over time, affecting their appearance and making routine cleaning essential.

With Airframe Dry Wash, aircraft exteriors can be cleaned efficiently without the need for water rinsing. Its highly concentrated formula removes surface contamination while leaving a protective coating that helps prevent future dirt build-up.

In this step-by-step guide, we'll show you how to use Airframe Dry Wash with the dry wash application method to achieve a clean, well-maintained aircraft exterior.

What is Aero-Sense® Airframe Dry Wash?

Aero-Sense® Airframe Dry Wash is a high-performance, ultra-concentrated cleaning solution developed specifically for the exterior cleaning of aircraft, including airplanes, helicopters and other aviation vehicles.

Its formulation effectively removes oil, grease, exhaust residue and general surface dirt, while providing a protective coating that helps prevent future contamination.

One of its key advantages is its waterless cleaning approach: the product does not require rinsing with water after application, making it a practical solution for aircraft exterior maintenance.

Airframe Dry Wash is certified according to several aviation industry standards, including Airbus AIMS09-00-002, AMS 1526C, AMS 1530C and Boeing BSS7432.

How to clean your aircraft using the dry wash application

Before getting started, make sure you have the necessary equipment ready:

Always consult the Safety Data Sheet (SDS) before use and prepare the aircraft according to the applicable aircraft cleaning or maintenance manual. You can request the SDS on the Airframe Dry Wash product page.

Step 1: Prepare the cleaning solution

Measure the required amount of concentrated Airframe Dry Wash and dilute it with water in a suitable pressure sprayer.

The recommended dilution ratio depends on the level of contamination:

  • 2% dilution: for regular cleaning.
  • 10% dilution: for heavily soiled surfaces.

Choose the appropriate concentration based on the condition of the aircraft.

Step 2: Spray the aircraft surface

Apply the diluted cleaning solution as a fine mist, ensuring that the surface is evenly covered.

For optimal results:

  • Maintain a consistent spray distance of approximately 20–30 cm (8–12 inches).
  • Work on manageable sections of approximately 1–2 m² at a time.
  • Ensure full and even coverage of the surface.

Working in smaller sections helps prevent the product from drying too quickly and ensures sufficient contact time.

Step 3: Allow the product to work

Let the cleaning solution work for approximately 15–30 seconds, depending on the level of soiling.

During this time, the product helps loosen dirt, oil and other contaminants, reducing the need for intensive wiping.

Important: Do not allow the cleaning solution to dry on the aircraft surface.

Step 4: Wipe away dirt and cleaning solution

Use a clean microfiber cloth or suitable cleaning applicator, such as a mop head or cleaning pad, to work the solution evenly across the surface.

Then, remove all cleaning agent and loosened dirt using a clean, dry microfiber cloth.

For the best results:

  • Use straight, overlapping wiping strokes to avoid streaks.
  • Fold the microfiber cloth into quarters and regularly change sides.
  • Replace cloths or cleaning pads when they become dirty to avoid transferring dirt back onto the surface.
  • Use gentle, even movements rather than scrubbing aggressively.

Step 5: Repeat if necessary

For heavily soiled areas, repeat the application process rather than scrubbing harder.

Apply a fresh layer of diluted Airframe Dry Wash, allow it to work for 15–30 seconds and wipe it off with a clean microfiber cloth.

This helps remove stubborn contamination while reducing the need for excessive mechanical action.

Step 6: Inspect the cleaned surface

Once cleaning is complete, inspect the treated area to ensure that all dirt and cleaning agent have been removed.

Check for any streaks or remaining product residue and, if necessary, wipe the surface again using a clean microfiber cloth.

Continue working in a consistent pattern, for example from top to bottom or from left to right, to ensure that no areas are missed.

Important tips for optimal cleaning results

A few additional considerations can help you get the most out of Airframe Dry Wash:

  • Avoid direct sunlight and hot surfaces. Ideally, perform dry wash cleaning inside a hangar. If this is not possible, work during cooler hours and treat smaller sections at a time. Never apply the product to hot surfaces.
  • Avoid cleaning in wet conditions. Do not apply Airframe Dry Wash during rainfall or when aircraft surfaces are wet. Moisture and product run-off can cause streaking and residue.
  • Use clean microfiber cloths. Regularly replace or change cloths and cleaning pads to prevent dirt from being transferred back onto the aircraft surface.
  • Test sensitive areas first. For sensitive surfaces, test the diluted solution on a small, inconspicuous area before proceeding with the full application.

Keep your aircraft clean with Aero-Sense®

Aero-Sense® Airframe Dry Wash offers an efficient solution for aircraft exterior cleaning without the need for water rinsing. By following the recommended application steps and using the correct dilution ratio, you can effectively remove dirt and contamination while leaving a protective coating on the surface.

Discover Aero-Sense® Airframe Dry Wash and explore our complete range of aircraft cleaning solutions.

Prefer a wash with rinsing? Read our guide on how to clean your aircraft with Airframe Cleaner, using foam application.

We'd like to hear from you

Questions, remarks, suggestions?
Feedback makes us better.