How to clean your aircraft with Airframe Cleaner, using foam application
A step-by-step guide to aircraft exterior cleaning with foam
Keeping an aircraft's exterior clean is an essential part of regular aircraft maintenance. Over time, oil, grease, exhaust residue and dirt build up on the airframe, affecting both the appearance of the aircraft and the condition of its surfaces.
With Aero-Sense® Airframe Cleaner and a foam application, you can clean large exterior surfaces efficiently and evenly. The foam clings to the surface, giving the cleaner time to loosen dirt before you brush and rinse it away.
In this video tutorial and step-by-step guide, we will guide you through the process of cleaning your aircraft with our Airframe Cleaner, using foam application.
What is Aero-Sense® Airframe Cleaner?
Aero-Sense® Airframe Cleaner is a concentrated detergent for general cleaning activities related to cleaning the exterior of airplanes, helicopters and other aircraft.
The product easily removes oil, grease, exhaust gas and dirt, and applies a coating that helps prevent the build-up of new dirt particles.
Its pH-neutral, non-corrosive and biodegradable formula is safe for use on:
- Metal and plastic surfaces
- Painted and unpainted surfaces
- De-icing boots
- Glass, Plexiglas® and Lexan®
- Windshields
Airframe Cleaner is certified according to several aviation industry standards, including Airbus AIMS09-00-002, AMS 1526C, Boeing BSS7432 and Douglas CSD No. 1.
How to clean your aircraft using foam application
Before you begin cleaning, gather all necessary equipment:
- Aero-Sense® Airframe Cleaner
- Foaming equipment
- Soft-bristle fibre brushes, cleaning cloths or sponges
- Water source (hose or bucket) with clean water
- Clean microfiber cloths for drying
- Protective gloves and other appropriate personal protective equipment
Always read the Safety Data Sheet (SDS) before use and prepare the aircraft for cleaning according to the aircraft cleaning or maintenance manual. You can request the SDS on the Airframe Cleaner product page.
Step 1: Prepare the cleaning solution
Fill the foaming equipment with Airframe Cleaner and water. Ensure the dilution ratio is set between 2 and 5%, depending on the level of dirt:
- 2% dilution: for light soiling and regular cleaning.
- Up to 5% dilution: for heavily soiled surfaces.
Step 2: Apply the foam
Apply the Airframe Cleaner foam evenly across the surface of your aircraft. Ensure that you cover all areas, paying special attention to heavily soiled spots.
Work in manageable sections, so you can treat each area before the product starts to dry.
Step 3: Allow the product to work
Allow the cleaner to work for approximately 5 minutes. During this time, the foam loosens oil, grease, exhaust residue and dirt from the surface.
Important: Do not let the product dry on the aircraft surface.
Step 4: Clean with a soft brush or washcloth
Use soft-bristle fibre brushes, a sponge or a washcloth to clean the surface gently. This helps to lift and remove dirt without damaging the paint or surface finish.
Use gentle, even movements rather than scrubbing aggressively.
Step 5: Rinse thoroughly
After cleaning, rinse the aircraft thoroughly with clean water to remove any remaining cleaner and dirt. Avoid water that contains minerals and ensure no residue is left behind.
Step 6: Dry the aircraft
Dry the aircraft using a clean microfiber cloth. This step helps to prevent water spots and streaks, leaving the surface clean and shiny.
Step 7: Final inspection
Perform a final inspection to ensure all areas are clean. If necessary, repeat any steps to achieve the desired cleanliness.
Important tips for optimal cleaning results
A few additional considerations can help you get the most out of Airframe Cleaner:
- Avoid direct sunlight and hot surfaces. Ideally, clean the aircraft inside a hangar or during cooler hours, so the product does not dry on the surface.
- Use the right dilution. Start with a 2% dilution for regular cleaning and only increase towards 5% for heavier soiling.
- Rinse with clean water. Water that contains minerals can leave spots and residue on the surface.
- Tackle insect residue separately. For stubborn insect residue on the airframe or windshield, use Aero-Sense® Insect Remover.
- Store the product correctly. Keep Airframe Cleaner in its original, tightly closed container in a cool, well-ventilated place and protect it from freezing. Its shelf life is 36 months.
Keep your aircraft clean with Aero-Sense®
Aero-Sense® Airframe Cleaner offers an efficient, all-purpose solution for aircraft exterior cleaning. By following the recommended application steps and using the correct dilution ratio, you can effectively remove dirt and contamination while leaving a protective coating on the surface.
Watch the video for a detailed demonstration of each step. Happy cleaning!
Discover Aero-Sense® Airframe Cleaner and explore our complete range of aircraft exterior cleaning solutions.
Looking for a waterless alternative? Read our guide on how to clean your aircraft with Aero-Sense® Airframe Dry Wash.